TOPCon has moved from a premium option to the default choice for many utility and commercial projects in India. Higher efficiency, a better temperature coefficient and strong bifacial performance have made n-type TOPCon modules the technology most procurement teams now shortlist first. Yet as deployment has scaled, independent test laboratories have flagged a reliability question that was largely absent from buyer checklists only a few years ago: UV-induced degradation, or UVID.
For a country where many large projects sit in high-irradiance regions such as Rajasthan and Gujarat, this is a practical question rather than an academic one. This article explains what UV-induced degradation in TOPCon modules is, what recent research actually shows, why standard certification may not catch it, and what developers, EPCs and lenders can ask suppliers before signing a purchase order.
What Is UV-Induced Degradation?
Ultraviolet light makes up only a small share of the solar spectrum, but it carries the most energy per photon. Over time, UV exposure can alter the thin layers on the front surface of a solar cell that provide passivation, the mechanism that limits the loss of charge carriers at the cell surface. When passivation weakens, more carriers recombine before they can be collected, and the module’s voltage and power output fall.
UVID is not a new phenomenon. Older module designs commonly used encapsulants containing UV absorbers that blocked much of this light before it reached the cell. Two industry shifts changed the picture. First, many manufacturers adopted UV-transparent encapsulants to capture more light and raise power ratings. Second, newer cell structures rely on very thin front-side layers, and research reported by pv magazine notes that thinner layers and certain silicon nitride compositions allow more UV to reach the sensitive interface beneath.
Why TOPCon Is in Focus
TOPCon is not the only technology affected. Fraunhofer ISE reported in 2024 that TOPCon, PERC and heterojunction cells can all suffer significant losses under UV irradiation, and Kiwa PVEL has also seen it in some PERC modules. TOPCon receives the most attention because it now dominates new shipments and because test results across TOPCon products have varied widely.
What the Research Shows
Several independent studies published between 2024 and 2026 give buyers a clearer view of the issue:
- Wide variation between products: In 2024 testing at a UV dose of 120 kWh/m², Kiwa PVEL reported losses of up to 16.6% in some n-type TOPCon modules, while roughly half of the modules in its scorecard lost less than 3%.
- A recurring test failure: In Kiwa PVEL’s 2025 Module Reliability Scorecard, UVID was among the most common test failures, alongside glass breakage and delamination.
- Partly recoverable losses: A peer-reviewed NREL study in Progress in Photovoltaics measured non-recoverable losses of 2.3% to 3.2% after a 60 kWh/m² UV dose, with additional losses during dark storage that recovered rapidly under sunlight.
- Cell-to-cell variability: The same study found large differences between cells within a single module, which the researchers linked to possible processing inconsistencies.
The Metastability Factor
One of the most important findings concerns how UVID is measured. Fraunhofer ISE found that TOPCon modules destabilise after UV exposure and lose further efficiency if they are left in the dark before testing. Once exposed to light again, much of that loss recovers. Its researchers concluded that conventional UV tests can significantly overstate real-world degradation unless modules are stabilised before measurement. A 2026 paper in EPJ Photovoltaics reached a similar conclusion, reporting a strong relationship between indoor UV testing and outdoor degradation once stabilisation was applied.
The takeaway for buyers is balanced. UVID is real, and some products are clearly more susceptible than others, but any headline loss figure from a laboratory test should be read alongside how the module was conditioned before it was measured.
Why Standard Certification May Not Catch It
In India, crystalline silicon modules require BIS registration under IS 14286, which is aligned with IEC 61215, together with IS/IEC 61730 for safety. The IEC 61215 qualification sequence includes a UV preconditioning test, MQT 10, at a dose of 15 kWh/m². That dose was designed to screen out the weakest products, not to simulate years of field exposure. Kiwa PVEL’s extended UVID test uses 120 kWh/m², which the laboratory estimates represents roughly six months to two years in the field, depending on location.
NREL researchers have also noted that UV exposure is under-represented in existing qualification tests, so a module can pass certification and still carry meaningful UV sensitivity. Certification remains essential, but it is a minimum threshold rather than a complete reliability picture.
Why It Matters for Indian Projects
UV dose accumulates with sunlight, so high-irradiance sites build up exposure faster than cloudier ones. Many of India’s largest solar parks are located in exactly these zones. Even a few percentage points of additional early-life loss can affect energy yield models, debt service coverage and the margin between expected and guaranteed performance.
There is also a measurement complication. Because affected TOPCon modules can degrade in darkness and recover in sunlight, samples tested after weeks in a warehouse, or removed from the field and stored indoors, may not reflect actual operating losses.
How the Industry Is Responding
Manufacturers and laboratories are addressing UVID at several levels:
- Cell-level optimisation: Refining front-side passivation and anti-reflection layers so the cell interface is more robust under UV exposure.
- Encapsulant selection: Using UV-blocking or light-converting encapsulants that shift UV photons to visible wavelengths, at some added material cost.
- Better test protocols: Developing UV ageing methods that include stabilisation steps, so laboratory results track field behaviour more closely.
Practical Questions to Ask Your Module Supplier
Procurement teams do not need to avoid TOPCon; they need better information. Consider asking:
- Extended UV data: Has this exact bill of materials been tested beyond the 15 kWh/m² MQT 10 dose, and at what dose?
- Stabilisation method: Were modules light-stabilised before final power measurement, and how?
- Independent verification: Are results available from third-party laboratories?
- Warranty alignment: How does the linear performance warranty treat early-life degradation, and how are claims assessed?
- Quality checks: What EL inspection and pre-dispatch testing is used to identify inconsistent cells?
UV-induced degradation in TOPCon modules is a genuine reliability consideration, but it is neither universal nor unmanageable. Research points to wide differences between products, partial recovery under sunlight and a clear need for test methods that reflect field conditions. For Indian developers and EPCs, the right response is informed procurement: request extended UV data, understand how it was measured, and insist on consistent materials and documented quality control. Buyers evaluating GREW Solar’s n-type TOPCon range can request technical documentation from the team.